Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
en:manual:reference_installation [2022/04/05 18:40] i3_relativism [Bootloader installation and configuration] remove further duplication |
en:manual:reference_installation [2022/12/22 02:45] throgh old revision restored (2022/04/05 19:00) |
||
---|---|---|---|
Line 527: | Line 527: | ||
<code bash> | <code bash> | ||
- | # pacman-key --populate hyperbola | + | # pacman-key --populate hyperbola |
</ | </ | ||
Line 534: | Line 534: | ||
</ | </ | ||
</ | </ | ||
- | |||
- | ==== Bootloader installation and configuration ==== | ||
- | === GRUB === | ||
- | Finally follow these steps: | ||
- | |||
- | <code bash> | ||
- | # pacman -S grub | ||
- | </ | ||
- | |||
- | <code bash> | ||
- | # grub-install --target=i386-pc --recheck /dev/sdX | ||
- | </ | ||
- | |||
- | < | ||
- | Here do NOT append a partition number, i.e. <color # | ||
- | </ | ||
- | |||
- | <code bash> | ||
- | # grub-mkconfig -o / | ||
- | </ | ||
- | |||
- | * To configure the bootloader, you have to install it and generate the file <color # | ||
- | |||
- | <note important> | ||
- | If you want to [[en: | ||
- | |||
- | <code bash> | ||
- | grub-install --no-bootsector /dev/sdX | ||
- | </ | ||
- | </ | ||
- | |||
- | <code bash> | ||
- | # grub-mkconfig -o / | ||
- | </ | ||
- | |||
- | * For BIOS and EFI: | ||
- | |||
- | <code bash> | ||
- | # pacstrap /mnt grub | ||
- | </ | ||
- | |||
- | * Install GRUB after chrooting (refer to the [[en: | ||
- | |||
- | See [[https:// | ||
- | |||
- | === Syslinux === | ||
- | <code bash> | ||
- | # pacstrap /mnt syslinux | ||
- | </ | ||
- | |||
- | See [[https:// | ||
==== Wireless tools installation ==== | ==== Wireless tools installation ==== | ||
Line 746: | Line 695: | ||
------------------------------ | ------------------------------ | ||
+ | ==== Bootloader installation and configuration ==== | ||
+ | === GRUB === | ||
+ | Finally follow these steps: | ||
+ | |||
+ | <code bash> | ||
+ | # pacman -S grub | ||
+ | </ | ||
+ | |||
+ | <code bash> | ||
+ | # grub-install --target=i386-pc --recheck /dev/sdX | ||
+ | </ | ||
+ | |||
+ | < | ||
+ | Here do NOT append a partition number, i.e. <color # | ||
+ | </ | ||
+ | |||
+ | <code bash> | ||
+ | # grub-mkconfig -o / | ||
+ | </ | ||
+ | |||
+ | * To configure the bootloader, you have to install it and generate the file <color # | ||
+ | |||
+ | <note important> | ||
+ | If you want to [[en: | ||
+ | |||
+ | <code bash> | ||
+ | grub-install --no-bootsector /dev/sdX | ||
+ | </ | ||
+ | </ | ||
+ | |||
+ | <code bash> | ||
+ | # grub-mkconfig -o / | ||
+ | </ | ||
+ | |||
+ | * For BIOS and EFI: | ||
+ | |||
+ | <code bash> | ||
+ | # pacstrap /mnt grub | ||
+ | </ | ||
+ | |||
+ | * Install GRUB after chrooting (refer to the [[en: | ||
+ | |||
+ | See [[https:// | ||
+ | |||
+ | === Syslinux === | ||
+ | <code bash> | ||
+ | # pacstrap /mnt syslinux | ||
+ | </ | ||
+ | |||
+ | See [[https:// | ||
* Configure <color # | * Configure <color # | ||
Line 759: | Line 758: | ||
* The efivars module is loaded. (<color # | * The efivars module is loaded. (<color # | ||
- | -------------------------------- | + | === Bootloader on external drive === |
- | + | ||
- | * Configure the network again for newly installed environment. See [[https:// | + | |
<note tip> | <note tip> | ||
If you are following the [[en: | If you are following the [[en: | ||
</ | </ | ||
+ | |||
+ | -------------- | ||
+ | |||
+ | * Configure the network again for newly installed environment. See [[https:// | ||
=== Configure speech support (for blind and visually impaired users) === | === Configure speech support (for blind and visually impaired users) === |