HyperWiki

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision 		Previous revision
Next revision Both sides next revision
en:manual:reference_installation [2022/04/05 18:38]
i3_relativism [Base system installation] 		en:manual:reference_installation [2022/04/05 18:52]
i3_relativism set bootloader section in right place
Line 534: Line 534:
 </code> </code>
 </note> </note>
- 
-==== Bootloader installation and configuration ==== 
-=== GRUB === 
-=== GRUB === 
-Finally follow these steps: 
- 
-<code bash> 
-# pacman -S grub 
-</code> 
- 
-<code bash> 
-# grub-install --target=i386-pc --recheck /dev/sda 
-</code> 
- 
-(Here do NOT append a partition number, i.e. <color #0B71B9/#DDF1FF>/dev/sdaX</color>) 
- 
-<code bash> 
-# grub-mkconfig -o /boot/grub/grub.cfg 
-</code> 
- 
-  * To configure the bootloader, you have to install it and generate the file <color #0B71B9/#DDF1FF>grub.cfg</color>: 
- 
-<code bash> 
-# grub-install /dev/sdX 
-</code> 
- 
-<note important> 
-If you want to [[en:manual:encrypted_installation|install GRUB on a Libreboot system]], keep in mind your system **does not use UEFI or Legacy BIOS**, but instead loads GRUB as its only payload. So you we will run this command instead: 
- 
-<code bash> 
-grub-install --no-bootsector /dev/sdX 
-</code> 
-</note> 
- 
-<code bash> 
-# grub-mkconfig -o /boot/grub/grub.cfg 
-</code> 
- 
-  * For BIOS and EFI: 
- 
-<code bash> 
-# pacstrap /mnt grub 
-</code> 
- 
-  * Install GRUB after chrooting (refer to the [[en:manual:reference_installation#Configure the system]] section). 
- 
-See [[https://wiki.parabola.nu/GRUB2|GRUB]] for further details. 
- 
-=== Syslinux === 
-<code bash>  
-# pacstrap /mnt syslinux 
-</code> 
- 
-See [[https://wiki.parabola.nu/Syslinux|Syslinux]] for further details. 
  
 ==== Wireless tools installation ==== ==== Wireless tools installation ====
Line 785: Line 731:
 # alsactl store # alsactl store
 </code> </code>
 +
 +==== Bootloader installation and configuration ====
 +=== GRUB ===
 +Finally follow these steps:
 +
 +<code bash>
 +# pacman -S grub
 +</code>
 +
 +<code bash>
 +# grub-install --target=i386-pc --recheck /dev/sdX
 +</code>
 +
 +<note>
 +Here do NOT append a partition number, i.e. <color #0B71B9/#DDF1FF>/dev/sdaX</color>)
 +</note>
 +
 +<code bash>
 +# grub-mkconfig -o /boot/grub/grub.cfg
 +</code>
 +
 +  * To configure the bootloader, you have to install it and generate the file <color #0B71B9/#DDF1FF>grub.cfg</color>:
 +
 +<note important>
 +If you want to [[en:manual:encrypted_installation|install GRUB on a Libreboot system]], keep in mind your system **does not use UEFI or Legacy BIOS**, but instead loads GRUB as its only payload. So you we will run this command instead:
 +
 +<code bash>
 +grub-install --no-bootsector /dev/sdX
 +</code>
 +</note>
 +
 +<code bash>
 +# grub-mkconfig -o /boot/grub/grub.cfg
 +</code>
 +
 +  * For BIOS and EFI:
 +
 +<code bash>
 +# pacstrap /mnt grub
 +</code>
 +
 +  * Install GRUB after chrooting (refer to the [[en:manual:reference_installation#Configure the system]] section).
 +
 +See [[https://wiki.parabola.nu/GRUB2|GRUB]] for further details.
 +
 +=== Syslinux ===
 +<code bash> 
 +# pacstrap /mnt syslinux
 +</code>
 +
 +See [[https://wiki.parabola.nu/Syslinux|Syslinux]] for further details.
  
 === Unmount and reboot === === Unmount and reboot ===