Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
en:guide:installation [2018/03/19 00:00]
emulatorman
en:guide:installation [2019/05/07 05:26]
emulatorman
Line 313: Line 313:
 noaccomp noccp nobsdcomp nodeflate nopcomp novj novjccomp"​ noaccomp noccp nobsdcomp nodeflate nopcomp novj novjccomp"​
   ​   ​
-rc_need_ppp0="​net.enp2s0f0"​+rc_net_ppp0_need="​net.enp2s0f0"​
 </​code>​ </​code>​
  
Line 342: Line 342:
 </​note>​ </​note>​
  
-To check that your computer has the correct time, enter **date** in the terminal.+To check that your computer has the correct time, enter <color #​620BB9/#​EEDDFF>​date</​color> ​in the terminal.
  
 <code bash> <code bash>
Line 490: Line 490:
  
   * Write your hostname to <color #​0B71B9/#​DDF1FF>/​etc/​hostname</​color>​   * Write your hostname to <color #​0B71B9/#​DDF1FF>/​etc/​hostname</​color>​
 +
 +<code bash>
 +# echo myhostname > /​etc/​hostname
 +</​code>​
 +
   * Symlink <color #​0B71B9/#​DDF1FF>/​etc/​localtime</​color>​ to <color #​0B71B9/#​DDF1FF>/​usr/​share/​zoneinfo/​Zone/​SubZone</​color>​. Replace <color #​620BB9/#​EEDDFF>​Zone</​color>​ and <color #​620BB9/#​EEDDFF>​Subzone</​color>​ to your liking. For example:   * Symlink <color #​0B71B9/#​DDF1FF>/​etc/​localtime</​color>​ to <color #​0B71B9/#​DDF1FF>/​usr/​share/​zoneinfo/​Zone/​SubZone</​color>​. Replace <color #​620BB9/#​EEDDFF>​Zone</​color>​ and <color #​620BB9/#​EEDDFF>​Subzone</​color>​ to your liking. For example:
  
Line 499: Line 504:
   * Add console keymap and font preferences in <color #​0B71B9/#​DDF1FF>/​etc/​conf.d/​keymaps</​color>​   * Add console keymap and font preferences in <color #​0B71B9/#​DDF1FF>/​etc/​conf.d/​keymaps</​color>​
   * Uncomment the selected locale in <color #​0B71B9/#​DDF1FF>/​etc/​locale.gen</​color>​ and generate it with <color #​620BB9/#​EEDDFF>​locale-gen</​color>​   * Uncomment the selected locale in <color #​0B71B9/#​DDF1FF>/​etc/​locale.gen</​color>​ and generate it with <color #​620BB9/#​EEDDFF>​locale-gen</​color>​
 +  * Set a root password with <color #​620BB9/#​EEDDFF>​passwd</​color>​
 +  * Add your user to the relevant [[https://​wiki.archlinux.org/​index.php/​Users_and_groups|group]] such as:
 +
 +<code bash>
 +# gpasswd -a YourActualUserName video
 +</​code>​
 +
   * Configure <color #​0B71B9/#​DDF1FF>/​etc/​mkinitcpio.conf</​color>​ as needed (see [[https://​wiki.archlinux.org/​index.php/​Mkinitcpio|mkinitcpio]]) and create an initial RAM disk with:   * Configure <color #​0B71B9/#​DDF1FF>/​etc/​mkinitcpio.conf</​color>​ as needed (see [[https://​wiki.archlinux.org/​index.php/​Mkinitcpio|mkinitcpio]]) and create an initial RAM disk with:
    
Line 516: Line 528:
 # grub-install /dev/sdX # grub-install /dev/sdX
 </​code>​ </​code>​
 +
 +<note important>​
 +If you want to [[en:​guide:​encrypted_installation|install GRUB on a Libreboot system]], keep in mind your system **does not use UEFI or Legacy BIOS**, but instead loads GRUB as its only payload. So you we will run this command instead:
 +
 +<code bash>
 +grub-install --no-bootsector /dev/sdX
 +</​code>​
 +</​note>​
  
 <code bash> <code bash>
Line 521: Line 541:
 </​code>​ </​code>​
  
-  * Set a root password with <color #​620BB9/#​EEDDFF>​passwd</​color>​ 
   * Configure the network again for newly installed environment. See [[https://​wiki.archlinux.org/​index.php/​Network_Configuration|Network Configuration]] and [[https://​wiki.parabola.nu/​Wireless_Setup|Wireless Setup]].   * Configure the network again for newly installed environment. See [[https://​wiki.archlinux.org/​index.php/​Network_Configuration|Network Configuration]] and [[https://​wiki.parabola.nu/​Wireless_Setup|Wireless Setup]].
  
- +<note tip> 
-Add your user to the relevant ​[[https://​wiki.archlinux.org/​index.php/​Users_and_groups|group]] such as: +If you are following ​the [[en:guide:​encrypted_installation|libreboot encrypted installation]] instructions,​ be sure to save copy of grub.cfg on a thumbdrive in case the one flashed to libreboot is incorrect. You can use the grub shell to boot from the extra copy. 
- +</note>
-<code bash> +
-# gpasswd -YourActualUserName video +
-</code>+
  
 ==== Configure speech support (for blind and visually impaired users) ==== ==== Configure speech support (for blind and visually impaired users) ====